s d m 1 1 9 h j a - 1 r 2 m f (a) (b) (d) (c) 1. part no. expression : (b) dimension code (c) inductance code : 1r2 = 1.20uh (a) series code 2. configuration & dimensions : a 4. materials : superworld electronics (s) pte ltd (a) core : e iron core (c) solder : sn99.95%-cu0.05% 3. schematic : (d) tolerance code : m = 20% (e) f : rohs compliant SDM119HJA series dip power choke coil pg. 1 15.03.2010 pcb pattern 11.5 max. 10.0 max. 3.40.5 bcd 11.5 max. (b) wire : enamelled copper wire unit:m/m e 6.60.5 a b ?w c d f ?w 1.50.1 10.0 max. 11.5 max. 11.5 max. 3.40.5 6.60.5 1.50.1 9.30.5 9.30.5 l series SDM119HJA-r30mf SDM119HJA-r47mf (e) 12.0 12.0 f 11.5 max. 11.5 max. SDM119HJA-r68mf SDM119HJA-1r2mf 9.30.5 1.50.1 6.60.5 11.5 max. 3.40.5 10.0 max. 10.0 max. 11.5 max. 3.40.5 1.30.1 6.60.5 9.30.5 e l g h e 6.60.5 6.60.5 6.60.5 6.60.5 f 0.50.2 0.50.2 0.50.2 0.50.2 g l 1.8 typ. 1.8 typ. 1.6 typ. 1.8 typ. h r32e yy.ww note : specifications subject to change without notice. please check our website for latest information.
superworld electronics (s) pte ltd note : specifications subject to change without notice. please check our website for latest information. pg. 2 15.03.2010 20% @ 0adc inductance l ( uh ) 0.47 0.30 6. electrical characteristics : SDM119HJA-r30mf SDM119HJA-r47mf part no. 36 36 0 irms max. ( a ) 0.40 60 50 0.60 dcr isat max. ( a ) ( m
) 8% 7. characteristics curves : f) part temperature (ambient + temp. rise) : shoul d not exceed 125c under worst case operating conditions. e) isat (a) : will cause l to drop approximately 20% d) irms (a) : will cause an approximately temp. rise ? t < 40c a) test frequency : 100khz/1.0v b) operating temp. : -25c to +125c c) ambient temp. : 20c 5. general specification : 0 20 40 min. q dip power choke coil SDM119HJA series 0.68 1.20 SDM119HJA-1r2mf SDM119HJA-r68mf 40 1.25 35 30 35 55 0.80 40 0 15304560 dc current (a) 0 0.1 0.2 0.3 0.4 0.5 indu c tan c e (uh) 0 10 20 30 40 50 60 70 80 90 100 temp. ri se( o c) dmpi119hja-r30m SDM119HJA-r30mf 0 15304560 dc current(a) 0 0.2 0.4 0.6 0.8 1 indu c t a n c e (uh) 0 10 20 30 40 50 60 70 80 90 100 temp. ri se( o c) dmpi119hja-r47m SDM119HJA-r47mf 0 1122334455 dc current (a) 0 0.2 0.4 0.6 0.8 1 indu c tan c e (uh) 0 10 20 30 40 50 60 70 80 90 100 temp. ri se( o c) dmpi119hja-r68m SDM119HJA-r68mf 0714212835 dc current(a) 0 0.6 1.2 1.8 2.4 3 indu c t a n c e (uh) 0 10 20 30 40 50 60 70 80 90 100 temp. ri se( o c) dmpi119hja-1r2m SDM119HJA-1r2mf
note : specifications subject to change without notice. please check our website for latest information. superworld electronics (s) pte ltd pg. 3 15.03.2010 7. characteristics curves : 0.3 0.05 0.1 0.001 SDM119HJA-r45mf SDM119HJA-r30mf 0.47 0.27 0.30 0.31 0.30 0.50 0.50 0.50 inductance (uh) 9.0 10 7.0 8.0 6.0 4.0 3.0 1.0 0.5 0.8 2.0 5.0 0.46 0.26 0.46 0.27 0.30 0.30 0.30 0.50 0.50 0.49 0.27 0.29 0.49 0.46 0.26 0.26 0.26 0.45 0.45 0.45 0.25 0.25 0.44 0.44 frequency ( mhz ) dip power choke coil SDM119HJA series 0.65 1.20 SDM119HJA-r68mf SDM119HJA-1r0mf 0.67 0.68 0.67 0.68 0.68 0.68 1.22 1.22 1.23 1.21 1.21 1.21 0.62 1.14 0.63 0.63 0.64 0.64 0.67 0.63 1.15 1.16 1.17 1.19 1.14 1.15 0.62 0.62 1.13 1.13 frequency ( mhz ) 65.2 49.4 47.6 48.8 68.1 76.1 SDM119HJA-r47mf 1.27 2.66 1.79 SDM119HJA-1r0mf SDM119HJA-r68mf 61.8 45.5 42.3 64.7 81.0 76.8 77.4 53.5 71.4 66.2 50.5 47.3 0.001 0.58 (uh) SDM119HJA-r30mf inductance 0.8 0.5 1.0 0.05 0.1 0.3 54.2 26.4 39.9 51.5 47.2 43.9 6.59 6.07 9.13 8.04 24.1 17.1 12.9 10.7 7.22 6.61 7.59 8.41 7.39 21.9 15.5 11.9 9.82 11.2 24.9 17.7 13.5 9.58 8.44 5.99 5.49 6.92 6.38 8.0 6.50 6.0 7.0 3.0 2.0 4.0 5.0 9.64 22.6 16.1 11.7 8.24 7.25 9.0 10 5.92 5.46 dmpi119hja - s er i es- z01 ?? ? ?? ? ?? ???? ??? ?? ? ?? frequency(mhz) inductance(uh) ??? ?? ?? ??? SDM119HJA series dmpi119hja - series - z0 1 ? ?? ?? ? ?? ??? ???? ??? ?? ? ?? frequency(m hz) q ??? ?? ?? ??? SDM119HJA series
superworld electronics (s) pte ltd note : specifications subject to change without notice. please check our website for latest information. pg. 4 15.03.2010 performance refer to standard electrical characteristics list should be covered with solder. more than 90% of the terminal electrode preheating 60 seconds 1. appearance : no significant abnormality 2. inductance change : within 10% of initial value preheating 60 seconds no disconnection or short circuit. 2. inductance : within 10% of initial value. 1. appearance : no damage no disconnection or short circuit. 2. inductance : within 10% of initial value. 1. appearance : no damage reliability test humidity resistance high temperature life test life test low temperature thermal shock solder heat resistance 150c 260c 150c 245c inductance electrical characteristics test dcr heat rated current (irms) solderability test mechanical performance test saturation current (isat) 8. reliability and test condition : item time : 50012 hours applied current : rated current humidity : 90% to 95% temperature : 405c temperature : 855c time : 50012 hours temperature (c) conditions of 1 cycle. temperature : -205c time : 50012 hours room temperature room temperature 1253 -253 recovery: 4 to 24hrs of recovery under the standard 2 total : 5 cycles 4 3 step 1 within 3 within 3 303 times (min.) 303 preheat : 150c, 60sec. solder : lead free solder temperature : 2605c flux : rosin dip time : 100.5sec. 100.5 seconds dipping cooling natural 41 seconds dipping cooling natural hp4284a or ch3302/13 20/1320s test condition isat(a) will cause lo to drop approximately 20% hioki3540 irms(a) will cause an temp rise < 40c typ. solder bath at 2455c for 5 seconds after fluxing, component shall be dipped in a melted condition after the removal from test chamber condition after the removal from test chamber recovery: 4 to 24hrs of recovery under the standard condition after the removal from test chamber recovery: 4 to 24hrs of recovery under the standard condition after the removal from test chamber recovery: 4 to 24hrs of recovery under the standard dip power choke coil SDM119HJA series appearance : cracking, chipping and any other random vibration test a period of 2 hours in each of 3 mutually perpendicular directions and times : x, y, z directions for 2 hours. amplitude : 1.52mm frequency : 10-55-10hz for 1 min. directions (total 6 hours). defects harmful to the characteristics should not be allowed.
superworld electronics (s) pte ltd note : specifications subject to change without notice. please check our website for latest information. pg. 5 15.03.2010 b) 280c tip temperature (max) temperature c e) use a 20 watt soldering iron with tip diameter of 1.0mm temperature c figure 1. re-flow soldering f) limit soldering time to 3 secs. d) 1.0mm tip diameter (max) 20~40s max. preheating 60~180s c) never contact the ceramic with the iron tip 150 natural soldering cooling over 1min. figure 2. iron soldering within 3secs. gradual cooling natural preheating soldering 150 350 300 cooling wave and re-flow soldering systems. if hand soldering cannot be avoi ded, the preferred technique is the utilization of hot by the difference in coefficients of expansion between solder, chip and substrate. our terminations are suitable for all mildly activated rosin fluxes are preferred. the minimum amount of solder can lead to damage from the stresses caused recommended temperature profiles for re-flow soldering in figure 1. products attachment with soldering iron is discouraged due to the inherent process control limitations. in the event that a soldering iron must be employed the following precautions are recommended. 9-2.1 solder re-flow : air soldering tools. a) preheat circuit and products to 150c. 9-2.2 soldering iron (figure 2) : note : 9-1. recommended pc board pattern 9. soldering and mounting : 9-2. soldering dip power choke coil SDM119HJA series 12.0 12.0 f h e l e 6.60.5 6.60.5 9.30.5 9.30.5 l series SDM119HJA-r30mf SDM119HJA-r47mf SDM119HJA-r68mf SDM119HJA-1r2mf 9.30.5 6.60.5 6.60.5 9.30.5 6.60.5 6.60.5 6.60.5 6.60.5 f 1.8 typ. 1.8 typ. 1.6 typ. 1.8 typ. h unit:m/m 200 217 tp(260c/10s max.) 480s max. 60~150s time(sec.)
superworld electronics (s) pte ltd note : specifications subject to change without notice. please check our website for latest information. pg. 6 15.03.2010 10. packing and quantity : inner box carton 756 1512 styrofoam size 108 SDM119HJA a) products should be handled with care to avoid damage or contamination from perspiration and skin oils. application notice 2. transportation : c) bulk handling should ensure that abrasion and mechanical shock are minimized. b) the use of tweezers or vacuum pick up is strongly recommended for individual components. c) the packaging material should be kept where no chlorine or sulfur exists in the air. b) recommended products should be used within 6 months from the time of delivery. a) temperature and humidity conditions : less than 30c and 70% rh. to maintain the solderabililty of terminal electrodes : 1. storage conditions : dip power choke coil SDM119HJA series
|
