|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
D a t a S h e e t , Rev. 1.0, O k t . 2 0 0 4 HYS64T32000HM-[3.7/5]-A HYS64T64020HM-[3.7/5]-A 214-Pin Micro-DIMM-DDR2-SDRAM Modules MDIMM DDR2 SDRAM RoHS Compliant Memory Products Never stop thinking. The information in this document is subject to change without notice. Edition 2004-10 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 Munchen, Germany (c) Infineon Technologies AG 2004. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. D a t a S h e e t , Rev. 1.0, O k t . 2 0 0 4 HYS64T32000HM-[3.7/5]-A HYS64T64020HM-[3.7/5]-A 214-Pin Micro-DIMM-DDR2-SDRAM Modules MDIMM DDR2 SDRAM RoHS Compliant Memory Products Never stop thinking. HYS64T32000HM-[3.7/5]-A, HYS64T64020HM-[3.7/5]-A Revision History: Previous Revision: Page All All Rev. 1.0 Rev. 0.6 2004-10 2004-06 Subjects (major changes since last revision) Documents contains only green products IDD Currents are final We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc.mp@infineon.com Template: mp_a4_v2.3_2004-01-14.fm HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Table of Contents 1 1.1 1.2 2 2.1 3 3.1 3.2 4 4.1 5 6 7 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 IDD Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 On Die Termination (ODT) Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 SPD Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Product Type Nomenclature (DDR2 DRAMs and DIMMs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 IDD Specifications and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Data Sheet 5 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X 214-Pin Micro-DIMM-DDR2-SDRAM Modules MDIMM HYS64T32000HM-[3.7/5]-A HYS64T64020HM-[3.7/5]-A 1 Overview This chapter gives an overview of the 1.8 V 214-Pin Micro-DIMM-DDR2-SDRAM Modules product family and describes its main characteristics. 1.1 * Features * * * * * * * * Burst Refresh, Distributed Refresh and Self Refresh All inputs and outputs SSTL_1.8 compatible Off-Chip Driver Impedance Adjustment (OCD) and On-Die Termination (ODT) Serial Presence Detect with E2PROM MDIMM Dimensions (nominal): 30 mm high, 54.0 mm wide Based on JEDEC standard reference layouts Raw Card "A" & "B" 2-piece type Mezzanine Socket with 0,4 mm contact centers RoHS Compliant Products1) * * * * 214-Pin PC2-4200 and PC2-3200 DDR2 SDRAM memory modules for use as main memory when installed in systems such as mobile personal computers. 32M x 64 and 64M x 64 module organization and 32M x 16 chip organization JEDEC standard Double-Data-Rate-Two Synchronous DRAMs (DDR2 SDRAM) with a single + 1.8 V ( 0.1 V) power supply Built with 512Mb DDR2 SDRAMs in P-TFBGA-84 chipsize packages Programmable CAS Latencies (3, 4 and 5), Burst Length (8 & 4) and Burst Type Performance -3.7 Table 1 Product Type Speed Code Speed Grade max. Clock Frequency @CL5 @CL4 @CL3 min. RAS-CAS-Delay min. Row Precharge Time min. Row Active Time min. Row Cycle Time -5 PC2-3200 3-3-3 200 200 200 15 15 40 55 Units -- MHz MHz MHz ns ns ns ns PC2-4200 4-4-4 fCK5 fCK4 fCK3 tRCD tRP tRAS tRC 266 266 200 15 15 45 60 1)RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers. Data Sheet 6 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Overview 1.2 Description The memory array is designed with 512Mb DoubleData-Rate-Two (DDR2) Synchronous DRAMs. Decoupling capacitors are mounted on the PCB board. The DIMMs feature serial presence detect based on a serial E2PROM device using the 2-pin I2C protocol. The first 128 bytes are programmed with configuration data and are write protected; the second 128 bytes are available to the customer. The INFINEON HYS64T[32/64]0[0/2]0HM-[3.7/5]-A module family are Unbuffered Micro-DIMM modules "MDIMMs" with 30,0 mm height based on DDR2 technology. DIMMs are available as non-ECC modules in 32M x 64 (256 MByte) and 64M x 64 (512 MByte) organization and density, intended for mounting into 214-Pin mezzanine connector sockets. Table 2 Ordering Information for RoHS Compliant Products Compliance Code2) Description SDRAM Technology 512 Mbit (x16) 512 Mbit (x16) 512 Mbit (x16) 512 Mbit (x16) Product Type1) PC2-3200 HYS64T32000HM-3.7-A 256MB 1Rx16 PC2-4200M-444-11-B1 1 rank Non-ECC HYS64T64020HM-3.7-A 512MB 2Rx16 PC2-4200M-444-11-A1 2 ranks Non-ECC PC2-4200 HYS64T32000HM-5-A HYS64T64020HM-5-A 256MB 1Rx16 PC2-3200M-333-11-B1 1 rank Non-ECC 512MB 2Rx16 PC2-3200M-333-11-A1 2 ranks Non-ECC 1) All part numbers end with a place code, designating the silicon die revision. Example: HYS64T32000HM-3.7-A, indicating Rev. "A" dies are used for DDR2 SDRAM components. For all INFINEON DDR2 module and component nomenclature see Chapter 7 of this data sheet. 2) The Compliance Code is printed on the module label and describes the speed grade, for example "PC2-4200M-444-11B1", where 4200M means Unbuffered Micro-DIMM modules with 4.26 GB/sec Module Bandwidth and "444-11" means Column Address Strobe (CAS) latency = 4, Row Column Delay (RCD) latency = 4 and Row Precharge (RP) latency = 4 using the latest JEDEC SPD Revision 1.1 and produced on the Raw Card "B". Table 3 DIMM Density 256 MByte 512 MByte Table 4 Address Format Module Organization 32M x 64 64M x 64 Memory Ranks 1 2 ECC/ Non-ECC Non-ECC Non-ECC # of SDRAMs 4 8 # of row/bank/column bits 13/2/10 13/2/10 Raw Card B A Components on Modules 1) DRAM Components2) HYB18T512160AF-3.7 HYB18T512160AF-3.7 HYB18T512160AF-5 HYB18T512160AF-5 DRAM Density 512 Mbit 512 Mbit 512 Mbit 512 Mbit DRAM Organisation 32M x 16 32M x 16 32M x 16 32M x 16 Product Type2) HYS64T32000HM-3.7 HYS64T64020HM-3.7 HYS64T32000HM-5 HYS64T64020HM-5 2) Green Product 1) For a detailed description of all functionalities of the DRAM components on these modules see the component data sheet. Data Sheet 7 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration 2 Pin Configuration The pin configuration of the DDR2 SDRAM Micro-DIMM is listed by function in Table 5 (214 pins). The abbreviations used in columns Pin and Buffer Type are explained in Table 6 and Table 7 respectively. The pin numbering is depicted in Figure 1. Table 5 Pin# Clock Signals 122 194 123 195 CK0 CK1 CK0 CK1 I I I I SSTL SSTL SSTL SSTL Clock Signals CK 1:0, Complement Clock Signals CK 1:0 Note: The system clock inputs. All address and command lines are sampled on the cross point of the rising edge of CK and the falling edge of CK. A Delay Locked Loop (DLL) circuit is driven from the clock inputs and output timing for read operations is synchronized to the input clock. Pin Configuration of MDIMM Name Pin Type Buffer Type Function 43 147 CKE0 CKE1 I I SSTL SSTL Clock Enables 1:0 Note: Activates the DDR2 SDRAM CK signal when HIGH and deactivates the CK signal when LOW. By deactivating the clocks, CKE0 initiates the Power Down Mode or the Self Refresh Mode. Note: 2-rank module Note: 1-rank module NC Control Signals 165 62 S0 S1 NC I I SSTL SSTL Chip Select Rank 1:0 Note: Enables the associated DDR2 SDRAM command decoder when LOW and disables the command decoder when HIGH. When the command decoder is disabled, new commands are ignored but previous operations continue. Rank 0 is selected by S0; Rank 1 is selected by S1. The input signals also disable all outputs (except CKE and ODT) of the register(d) on the DIMM when both inputs are high. When S is HIGH, all register outputs (except CK, ODT and Chip select) remain in the previous state. Note: 2-rank module Note: 1-rank module NC 163 60 56 RAS CAS WE NC I I I SSTL SSTL SSTL Row Address Strobe (RAS), Column Address Strobe (CAS), Write Enable (WE) Note: When sampled at the cross point of the rising edge of CK,and falling edge of CK, RAS, CAS and WE define the operation to be executed by the SDRAM. Bank Address Bus 1:0 Note: Select internal SDRAM memory bank Address Signals 55 162 BA0 BA1 I I SSTL SSTL Data Sheet 8 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration Table 5 Pin# 46 Pin Configuration of MDIMM (cont'd) Name BA2 NC 161 159 52 158 51 50 157 48 155 154 54 47 153 167 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 AP A11 A12 A13 NC Pin Type I NC I I I I I I I I I I I I I I I NC Buffer Type SSTL - SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL - Address Input 13 Note: modules based on x4/x8 component Note: modules based on x16 component Function Bank Address Bus 2 Note: greater than 512Mb DDR2 SDRAMS Note: less than 1Gb DDR2 SDRAMS Address Inputs 12:0, Address Input 10/Autoprecharge Note: During a Bank Activate command cycle, defines the row address when sampled at the crosspoint of the rising edge of CK and falling edge of CK. During a Read or Write command cycle, defines the column address when sampled at the cross point of the rising edge of CK and falling edge of CK. In addition to the column address, AP is used to invoke autoprecharge operation at the end of the burst read or write cycle. If AP is HIGH, autoprecharge is selected and BA[1:0] defines the bank to be precharged. If AP is LOW, autoprecharge is disabled. During a Precharge command cycle, AP is used in conjunction with BA[1:0] to control which bank(s) to precharge. If AP is HIGH, all banks will be precharged regardless of the state of BA[1:0] inputs. If AP is LOW, then BA[1:0] are used to define which bank to precharge. Data Sheet 9 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration Table 5 Pin# Data Signals 3 4 9 10 109 110 114 115 12 13 21 22 117 118 125 126 24 25 30 31 128 129 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Data Bus 63:0 Note: Data Input/Output pins Pin Configuration of MDIMM (cont'd) Name Pin Type Buffer Type Function Data Sheet 10 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration Table 5 Pin# 133 134 33 34 38 39 136 137 142 143 67 68 73 74 174 175 179 180 76 77 81 82 182 183 188 189 84 85 92 93 191 192 200 201 95 96 101 102 203 204 Pin Configuration of MDIMM (cont'd) Name DQ22 DQ23 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 Pin Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Function Data Bus 63:0 Data Sheet 11 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration Table 5 Pin# 208 209 7 6 19 18 28 27 140 139 71 70 186 185 198 197 99 98 112 120 131 36 177 79 90 206 EEPROM 105 SCL I CMOS Serial Bus Clock Note: This signal is used to clock data into and out of the SPD EEPROM. 104 SDA I/O OD Serial Bus Data Note: This is a bidirectional pin used to transfer data into or out of the SPD EEPROM. A resistor must be connected from SDA to VDDSPD on the motherboard to act as a pull-up. 211 213 SA0 SA1 I I CMOS CMOS Serial Address Select Bus 1:0 Note: Address pins used to select the Serial Presence Detect base address. I/O Reference Voltage Note: Reference voltage for the SSTL-18 inputs. Pin Configuration of MDIMM (cont'd) Name DQ62 DQ63 DQS0 DQS0 DQS1 DQS1 DQS2 DQS2 DQS3 DQS3 DQS4 DQS4 DQS5 DQS5 DQS6 DQS6 DQS7 DQS7 DM0 DM1 DM2 DM3 DM4 DM5 DM6 DM7 Pin Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I I I I I I Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Data Masks 7:0 Note: The data write masks, associated with one data byte. In Write mode, DM operates as a byte mask by allowing input data to be written if it is LOW but blocks the write operation if it is HIGH. In Read mode, DM lines have no effect. Note: x8 based module Data Strobes 7:0 Note: The data strobes, associated with one data byte, sourced with data transfers. In Write mode, the data strobe is sourced by the controller and is centered in the data window. In Read mode the data strobe is sourced by the DDR2 SDRAM and is sent at the leading edge of the data window. DQS signals are complements, and timing is relative to the crosspoint of respective DQS and DQS. If the module is to be operated in single ended strobe mode, all DQS signals must be tied on the system board to VSS and DDR2 SDRAM mode registers programmed appropriately. Note: See block diagram for corresponding DQ signals Function Data Bus 63:0 Power Supplies 1 VREF AI - Data Sheet 12 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration Table 5 Pin# Pin Configuration of MDIMM (cont'd) Name Pin Type PWR Buffer Type - Function Power Supply Note: Power and ground for the DDR SDRAM 42, 45, 49, 53, VDD 57, 61, 64, 146, 149, 152, 156, 160, 164, 168, 171 107 VDDSPD PWR - EEPROM Power Supply Note: Serial EEPROM positive power supply, wired to a separate power pin at the connector which supports from 1.7 Volt to 3.6 Volt. 2, 5, 8, 11, 14, VSS 17, 20, 23, 26, 29, 32, 35, 37, 40, 66, 69, 72, 75, 78, 80, 83, 86, 89, 91, 94, 97, 100, 103, 108, 111, 113, 116, 119, 121, 124, 127, 130, 132, 135, 138, 141, 144, 173, 176, 178, 181, 184, 187, 190, 193, 196, 205, 199, 202, 207, 210 Other Pins 166 63 ODT0 ODT1 GND - Ground Plane Note: Power and ground for the DDR SDRAM I I SSTL SSTL On-Die Termination Control 1:0 Note: Asserts on-die termination for DQ, DM, DQS, and DQS signals if enabled via the DDR2 SDRAM mode register. Note: 2-rank module Note: 1-rank module NC 15, 16, 41, 44, NC 46, 58, 59, 65, 87, 88, 106, 145, 148, 150, 151, 167, 169, 170, 172, 212, 214 NC - Not connected Note: Pins not connected on Infineon MDIMMs Data Sheet 13 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration Table 6 Abbreviation I O I/O AI PWR GND NC Abbreviations for Pin Type Description Standard input-only pin. Digital levels. Output. Digital levels. I/O is a bidirectional input/output signal. Input. Analog levels. Power Ground Not Connected Table 7 Abbreviation SSTL Abbreviations for Buffer Type Description Serial Stub Terminated Logic (SSTL_18) CMOS Levels Open Drain. The corresponding pin has 2 operational states, active low and tristate, and allows multiple devices to share as a wire-OR. CMOS OD Data Sheet 14 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration DQ0 VSS DQS0 DQ2 VREF - Pin 001 - Pin 003 - Pin 005 - Pin 007 - Pin 009 Pin Pin Pin Pin 011 013 015 017 V SS - Pin 002 DQ1 - Pin 004 DQS0 - Pin 006 V SS DQ3 DQ8 V SS Pin 008 Pin 010 Pin 012 Pin 109 - DQ4 Pin 111 - V SS Pin 113 - V SS Pin 115 - DQ7 Pin 117 - DQ12 Pin 119 - V SS Pin Pin Pin Pin 121 123 125 127 - V SS - CK0 - DQ14 - V SS Pin 108 - VSS Pin 110 - DQ5 Pin 112 - DM0 Pin 114 - DQ6 Pin 116 - VSS Pin Pin Pin Pin 118 120 122 124 DQ13 DM1 CK0 VSS VSS DQ9 NC VSS DQS1 - Pin 019 DQ10 - Pin 021 VSS - Pin 023 DQ17 - Pin 025 DQS2 - Pin 027 VSS - Pin 029 DQ19 - Pin 031 DQ24 - Pin 033 VSS - Pin 035 VSS - Pin 037 DQ27 - Pin 039 NC - Pin 041 CKE0 - Pin 043 VDD - Pin 045 A11 VDD A4 VDD Pin Pin Pin Pin 047 049 051 053 Pin 014 NC - Pin 016 DQS1 - Pin 018 V SS - Pin 020 DQ11 - Pin 022 DQ16 - Pin 024 V SS - Pin 026 DQS2 DQ18 V SS DQ25 DM3 DQ26 V SS VDD Pin Pin Pin Pin Pin Pin Pin Pin 028 030 032 034 036 038 040 042 Pin 129 - DQ21 Pin 131 - DM2 Pin 133 - DQ22 Pin Pin Pin Pin Pin Pin Pin Pin 135 137 139 141 143 145 147 149 V SS DQ29 DQS3 V SS DQ31 NC CKE1/NC V DD Pin 126 - DQ15 Pin 128 - DQ20 Pin 130 - VSS Pin 132 - VSS Pin 134 - DQ23 Pin 136 - DQ28 Pin 138 - VSS Pin Pin Pin Pin 140 142 144 146 DQS3 DQ30 VSS NC - Pin 044 NC/BA2 - Pin 046 A7 - Pin 048 A5 A2 A10/AP WE NC CAS S1/NC VDD Pin Pin Pin Pin Pin Pin Pin Pin 050 052 054 056 058 060 062 064 Pin 151 - NC Pin 153 - A12 Pin 155 - A8 Pin Pin Pin Pin Pin Pin Pin Pin 157 159 161 163 165 167 169 171 A6 A1 A0 RAS S0 NC NC V DD VDD Pin 148 - NC Pin 150 - NC Pin 152 - VDD Pin 154 - A9 Pin 156 - VDD Pin 158 - A3 Pin 160 - VDD Pin Pin Pin Pin 162 164 166 168 BA1 VDD ODT0 BA0 - Pin 055 VDD - Pin 057 NC - Pin 059 VDD - Pin 061 ODT1/NC - Pin 063 NC - Pin 065 DQ32 - Pin 067 VSS DQS4 DQ34 VSS Pin Pin Pin Pin 069 071 073 075 V SS - Pin 066 DQ33 - Pin 068 DQS4 - Pin 070 V SS DQ35 DQ40 V SS V SS DQ43 DQ48 V SS NC DM6 DQ50 V SS Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin 072 074 076 078 080 082 084 086 088 090 092 094 Pin 173 - V SS Pin 175 - DQ37 Pin 177 - DM4 Pin Pin Pin Pin Pin Pin Pin Pin 179 181 183 185 187 189 191 193 DQ38 V SS DQ45 DQS5 V SS DQ47 DQ52 V SS VDD Pin 170 - NC Pin 172 - NC Pin 174 - DQ36 Pin 176 - VSS Pin 178 - VSS Pin 180 - DQ39 Pin 182 - DQ44 Pin Pin Pin Pin 184 186 188 190 VSS DQS5 DQ46 DQ41 - Pin 077 DM5 - Pin 079 DQ42 - Pin 081 VSS - Pin 083 DQ49 - Pin 085 NC - Pin 087 VSS - Pin 089 VSS DQ51 DQ56 VSS Pin Pin Pin Pin 091 093 095 097 Pin 195 - CK1 Pin 197 - DQS6 Pin 199 - V SS Pin 201 - DQ55 Pin 203 - DQ60 Pin 205 - V SS Pin 207 - V SS Pin 209 - DQ63 Pin 211 - SA0 Pin 213 - SA1 DQS7 - Pin 099 DQ58 - Pin 101 VSS - Pin 103 SCL - Pin 105 V DDSPD - Pin 107 DQ57 - Pin 096 DQS7 - Pin 098 V SS - Pin 100 DQ59 - Pin 102 SDA - Pin 104 NC - Pin 106 VSS Pin 192 - DQ53 Pin 194 - CK1 Pin 196 - VSS Pin 198 - DQS6 Pin 200 - DQ54 Pin 202 - VSS Pin 204 - DQ61 Pin Pin Pin Pin 206 208 210 212 DM7 DQ62 VSS NC Pin 214 - NC MPPT0060 Figure 1 Pin Configuration for Two-Piece Mezzanine Socket on MDIMM (214 pins) Data Sheet 15 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration 2.1 BA0 - BA1 A0 - An RAS CAS WE CKE0 CKE1 ODT0 ODT1 CK0 CK0 CK1 CK1 S0 S1 DM0 DQS0 DQS0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DM1 DQS1 DQS1 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 Block Diagrams BA0 - BA1: SDRAMs D0 - D7 A0 - An: SDRAMs D0 - D7 RAS: SDRAMs D0 - D7 CAS: SDRAMs D0 - D7 WE: SDRAMs D0 - D7 CKE0: SDRAMs D0 - D3 CKE1: SDRAMs D4 - D7 ODT0: SDRAMs D0 - D3 ODT1: SDRAMs D4 - D7 4 loads 4 loads VDD,SPD VDD/VDDQ VREF VSS VDD: SPD EEPROM E0 VDD/VDDQ: SDRAMs D0 - D7 VREF: SDRAMs D0 - D7 VSS: SDRAMs D0 - D7 SCL SDA SA0 SA1 SA2 VSS SCL SDA A0 A1 A2 WP E0 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 D0 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 D4 DM4 DQS4 DQS4 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DM5 DQS5 DQS5 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 D5 DM6 DQS6 DQS6 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DM7 DQS7 DQS7 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 D2 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 CS LDM LDQS LDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDM UDQS UDQS I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 D6 D1 D3 D7 DM2 DQS2 DQS2 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DM3 DQS3 DQS3 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 MPBT0010 Figure 2 Notes Block Diagram Raw Card A Micro-DIMM (x64, 2 Ranks, x16) 2. S0, S1, BAn, An, RAS, CAS, WE, ODTO, ODT1, CKEO, CKE1 resistors are 3 5 % 1. DQ, DQS, DM resistors are 22 5 % Data Sheet 16 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Pin Configuration %$ %$ $ $Q 5$6 &$6 :( 966 &.( 2'7 6 &. &. &. &. 6&/ 6'$ 6$ 6$ ORDGV ORDGV 6&/ 6'$ $ $ $ :3 %$ %$ 6'5$0V ' ' $ $Q 6'5$0V ' ' 5$6 6'5$0V ' ' &$6 6'5$0V ' ' :( 6'5$0V ' ' 966 6'5$0V ' ' &.( 6'5$0V ' ' 2'7 6'5$0V ' ' 9''63' 9''9''4 95() 966 9'' 63' ((3520 ( 9''9''4 6'5$0V ' ' 95() 6'5$0V ' ' 966 6'5$0V ' ' ( 9VV '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 /'0 &6 /'46 /'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 8'0 8'46 8'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 /'0 &6 /'46 /'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 8'0 8'46 8'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ' '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 '0 '46 '46 '4 '4 '4 '4 '4 '4 '4 '4 /'0 &6 /'46 /'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 8'0 8'46 8'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 /'0 &6 /'46 /'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 8'0 8'46 8'46 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 ' ' ' Figure 3 Notes Block Diagram Raw Card B Micro-DIMM (x64, 1 Rank, x16) 03%7 1. DQ, DQS, DM resistors are 22 5 % 2. S0, BAn, An, RAS, CAS, WE, ODTO, CKEO resistors are 3 5 % 3. Load matching Capacitors on BA0 - BA1, A0 - An, RAS, CAS, WE, with 8 pF 0.5pF Data Sheet 17 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules IDD Specifications and Conditions 3 Table 8 Parameter IDD Specifications and Conditions IDD Measurement Conditions 1)2)3)4)5)6) Symbol Operating Current 0 One bank Active - Precharge; tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING. IDD0 Operating Current 1 IDD1 One bank Active - Read - Precharge; IOUT = 0 mA, BL = 4, tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, tRCD = tRCD.MIN, AL = 0, CL = CLMIN; CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING. Precharge Standby Current All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING. Precharge Power-Down Current Other control and address inputs are STABLE, Data bus inputs are FLOATING. IDD2N IDD2P Precharge Quiet Standby Current IDD2Q All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are STABLE, Data bus inputs are FLOATING. Active Standby Current Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX, tRP = tRP.MIN; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; IOUT = 0 mA. Active Power-Down Current All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs are FLOATING. MRS A12 bit is set to LOW (Fast Power-down Exit); Active Power-Down Current All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs are FLOATING. MRS A12 bit is set to HIGH (Slow Power-down Exit); Operating Current Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX., tRP = tRP.MIN; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; IOUT = 0 mA. IDD3N IDD3P(0) IDD3P(1) IDD4R Operating Current IDD4W Burst Write: All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX., tRP = tRP.MAX; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; Burst Refresh Current IDD5B tCK = tCK.MIN., Refresh command every tRFC = tRFC.MIN interval, CKE is HIGH, CS is HIGH between valid commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING. Distributed Refresh Current IDD5D tCK = tCK.MIN., Refresh command every tRFC = tREFI interval, CKE is LOW and CS is HIGH between valid commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING. Data Sheet 18 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules IDD Specifications and Conditions Table 8 Parameter Self-Refresh Current CKE 0.2 V; external clock off, CK and CK at 0 V; Other control and address inputs are FLOATING, Data bus inputs are FLOATING. IDD6 current values are guaranteed up to TCASE of 85 C max. IDD Measurement Conditions (cont'd)1)2)3)4)5)6) Symbol IDD6 All Bank Interleave Read Current IDD7 All banks are being interleaved at minimum tRC without violating tRRD using a burst length of 4. Control and address bus inputs are STABLE during DESELECTS. Iout = 0 mA. 1) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V 2) IDD specifications are tested after the device is properly initialized and IDD parameter are specified with ODT disabled. 3) Definitions for IDD: LOW is defined as VIN VIL(ac).MAX, HIGH is defined as VIN VIH(ac).MIN STABLE is defined as: inputs are stable at a HIGH or LOW level FLOATING is defined as: inputs are VREF = VDDQ /2 SWITCHING is defined as: inputs are changing between HIGH and LOW every other clock (once per 2 cycles) for address and control signals, and inputs changing between HIGH and LOW every other data transfer (once per cycle) for DQ signals not including mask or strobes. 4) IDD1, IDD4R and IDD7 current measurements are defined with the outputs disabled (IOUT = 0 mA). To achieve this on module level the output buffers can be disabled using an EMRS(1) (Extended Mode Register Command) by setting A12 bit to HIGH. 5) For two rank modules: for all active current measurements the other rank is in Precharge Power-Down Mode IDD2P 6) For details and notes see the relevant INFINEON component data sheet Data Sheet 19 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules IDD Specifications and Conditions Table 9 IDD Specification for HYS64T[32000/64020]HM-3.7-A HYS64T32000HM-3.7-A HYS64T64020HM-3.7-A Unit Notes1) Organization Product Type 256MB 1 Rank x64 -3.7 512MB 2 Ranks x64 -3.7 Max. 340 380 320 30 240 320 130 40 420 460 540 50 16 900 mA mA mA mA mA mA mA mA mA mA mA mA mA mA 2) 2) 3) 3) 3) 3) 3) 3) 2) 2) 3) 2) 3) 2) Symbol Max. 320 360 160 20 120 160 60 20 400 440 520 20 8 880 IDD0 IDD1 IDD2N IDD2P IDD2Q IDD3N IDD3P( MRS = 0) IDD3P( MRS = 1) IDD4R IDD4W IDD5B IDD5D IDD6(L) IDD7 1) Calculated values from component data. ODT disabled. IDD1, IDD4R and IDD7 are defined with the outputs disabled 2) The other rank is in IDD2P Precharge Power-Down Standby Current mode 3) Both ranks are in the same IDD mode Data Sheet 20 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules IDD Specifications and Conditions Table 10 IDD Specification for HYS64T[32000/64020]HM-5-A HYS64T64020HM-5-A HYS64T32000HM-5-A Unit Notes1) Organization Product Type 256MB 1 Rank x64 -5 512MB 2 Ranks x64 -5 Max. 300 320 260 30 200 280 100 40 360 380 500 50 16 860 mA mA mA mA mA mA mA mA mA mA mA mA mA mA 2) 2) 3) 3) 3) 3) 3) 3) 2) 2) 3) 2) 3) 2) Symbol Max. 280 300 130 20 100 140 50 20 340 360 480 20 8 840 IDD0 IDD1 IDD2N IDD2P IDD2Q IDD3N IDD3P( MRS = 0) IDD3P( MRS = 1) IDD4R IDD4W IDD5B IDD5D IDD6(L) IDD7 1) Calculated values from component data. ODT disabled. IDD1, IDD4R and IDD7 are defined with the outputs disabled 2) The other rank is in IDD2P Precharge Power-Down Standby Current mode 3) Both ranks are in the same IDD mode Data Sheet 21 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules IDD Specifications and Conditions 3.1 IDD Test Conditions For testing the IDD parameters, the timing parameters as in Table 11 are used. Table 11 Parameter CAS Latency IDD Measurement Test Conditions Symbol -3.7 4 3.75 15 60 7.5 10 45 70000 15 105 7.8 -5 3 5 15 55 7.5 10 40 70000 15 105 7.8 Unit PC2-4200-4-4-4 PC2-3200-3-3-3 CL(IDD) Clock Cycle Time tCK(IDD) Active to Read or Write delay tRCD(IDD) Active to Active / Auto-Refresh command period tRC(IDD) 1) Active bank A to Active bank B command delay x8 tRRD(IDD) 2) x16 tRRD(IDD) Active to Precharge Command tRAS.MIN(IDD) tRAS.MAX(IDD) Precharge Command Period tRP(IDD) Auto-Refresh to Active / Auto-Refresh command period tRFC(IDD) Average periodic Refresh interval tREFI 1) For modules based on x8 components 2) For modules based on x16 components tCK ns ns ns ns ns ns ns ns ns s 3.2 On Die Termination (ODT) Current current consumption for any terminated input pin, depends on the input pin is in tri-state or driving 0 or 1, as long a ODT is enabled during a given period of time. The ODT function adds additional current consumption to the DDR2 SDRAM when enabled by the EMRS(1). Depending on address bits A[6,2] in the EMRS(1) a "weak" or "strong" termination can be selected. The Table 12 Parameter ODT current per terminated pin Symbol Min. 5 2.5 10 5 Typ. 6 3 12 6 Max. Unit 7.5 3.75 15 7.5 EMRS(1) State Enabled ODT current per DQ IODTO ODT is HIGH; Data Bus inputs are FLOATING Active ODT current per DQ ODT is HIGH; worst case of Data Bus inputs are STABLE or SWITCHING. mA/DQ A6 = 0, A2 = 1 mA/DQ A6 = 1, A2 = 0 mA/DQ A6 = 0, A2 = 1 mA/DQ A6 = 1, A2 = 0 IODTT Note: For power consumption calculations the ODT duty cycle has to be taken into account Data Sheet 22 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Electrical Characteristics 4 4.1 Table 13 Parameter Electrical Characteristics Operating Conditions Absolute Maximum Ratings Symbol Values Min. Max. 2.3 2.3 2.3 95 V V V % - 0.5 - 1.0 - 0.5 5 Unit Note/Test Condition 1) 1) 1) 1) VIN, VOUT Voltage on VDD relative to VSS VDD Voltage on VDDQ relative to VSS VDDQ Storage Humidity (without condensation) HSTG Voltage on any pins relative to VSS 1) Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and device functional operation at or above the conditions indicated is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 14 Parameter Operating Conditions Symbol Values Min. Max. +55 +95 +100 +105 90 C C C kPa % 5) 1)2)3)4) Unit Notes Operating temperature (ambient) DRAM Case Temperature Storage Temperature Barometric Pressure (operating & storage) Operating Humidity (relative) TOPR TCASE TSTG PBar 0 0 -55 +69 10 HOPR 1) DRAM Component Case Temperature is the surface temperature in the center on the top side of any of the DRAMs. 2) Within the DRAM Component Case Temperature Range all DRAM specifications will be supported 3) Above 85 C DRAM Case Temperature the Auto-Refresh command interval has to be reduced to tREFI = 3.9 s 4) Self-Refresh period is hard-coded in the DRAMs and therefore it is imperative that the system ensures the DRAM is below 85 C Case Temperature before initiating Self-Refresh operation. 5) Up to 3000 m. Table 15 Parameter Supply Voltage Levels and DC Operating Conditions Symbol VDD VDDQ Values Min. Nom. 1.8 1.8 0.5 x VDDQ -- -- -- -- Max. 1.9 1.9 0.51 x VDDQ 3.6 VDDQ + 0.3 VREF - 0.125 5 V V V V V V A 3) 1) 2) Unit Notes Device Supply Voltage Output Supply Voltage Input Reference Voltage SPD Supply Voltage DC Input Logic High DC Input Logic Low In / Output Leakage Current 1.7 1.7 0.49 x VDDQ 1.7 VREF + 0.125 - 0.30 -5 VREF VDDSPD VIH (DC) VIL (DC) IL 1) Under all conditions, VDDQ must be less than or equal to VDD 2) Peak to peak AC noise on VREF may not exceed 2% VREF(DC). VREF is also expected to track noise in VDDQ. 3) Input voltage for any connector pin under test of 0 V VIN VDDQ + 0.3 V; all other pins at 0 V. Current is per pin Data Sheet 23 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Electrical Characteristics Table 16 Speed Grade Definition Speed Bins DDR2-533C -3.7 4-4-4 Symbol @ CL = 3 @ CL = 4 @ CL = 5 Min. 5 3.75 3.75 45 60 15 15 Max. 8 8 8 70000 -- -- -- DDR2-400B -5 3-3-3 Min. 5 5 5 40 55 15 15 Max. 8 8 8 70000 -- -- -- Unit Notes Speed Grade IFX Sort Name CAS-RCD-RP latencies Parameter Clock Frequency tCK -- ns ns ns ns ns ns ns 1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4) Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time tCK tCK tCK tRAS tRC tRCD tRP 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) only. 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode 3) Inputs are not recognized as valid until recognized as low. 5) VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is 4) The output timing reference voltage level is VTT. tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. Timing Parameter by Speed Grade - DDR2-400B & DDR2-533C Symbol -3.7 DDR2-533 4-4-4 Min. Max. +500 -- 0.55 -- 0.55 -- -- -500 2 0.45 3 0.45 WR + tRP -5 DDR2-400 3-3-3 Min. -600 2 0.45 3 0.45 WR + tRP Max. +600 -- 0.55 -- 0.55 -- -- ps Unit Notes1) Table 17 Parameter DQ output access time from CK / CK CK, CK high-level width width CK, CK low-level width Auto-Precharge write recovery + precharge time Minimum time clocks remain ON after CKE asynchronously drops LOW DQ and DM input hold time (differential data strobe) tAC CAS A to CAS B command period tCCD tCH CKE minimum high and low pulse tCKE tCL tDAL tDELAY tCK tCK tCK tCK tCK ns tIS + tCK + tIH tIS + tCK + tIH 275 25 0.35 -500 tDH(base) 225 -- -- -- +450 -- -- -- +500 ps ps DQ and DM input hold time (single tDH1(base) -25 ended data strobe) DQ and DM input pulse width (each tDIPW input) DQS output access time from CK / tDQSCK CK Data Sheet 0.35 -450 tCK ps 24 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Electrical Characteristics Table 17 Parameter Timing Parameter by Speed Grade - DDR2-400B & DDR2-533C (cont'd) Symbol -3.7 DDR2-533 4-4-4 Min. DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) Write command to 1st DQS latching transition DQ and DM input setup time (differential data strobe) DQ and DM input setup time (single ended data strobe) DQS falling edge hold time from CK (write cycle) Max. -- 300 0.35 -- WL - 0.25 -5 DDR2-400 3-3-3 Min. 0.35 -- Max. -- 350 Unit Notes1) tDQSL,H tDQSQ tDQSS tCK ps WL + 0.25 WL - 0.25 -- -- -- -- 150 25 0.2 0.2 WL + 0.25 tCK -- -- -- -- ps ps tDS(base) 100 tDS1(base) -25 tDSH 0.2 0.2 tCK tCK DQS falling edge to CK setup time tDSS (write cycle) Clock half period Data-out high-impedance time from CK / CK Address and control input pulse width (each input) Address and control input setup time tHP tHZ MIN. (tCL, tCH) -- 375 0.6 MIN. (tCL, tCH) -- 475 0.6 tAC.MAX -- -- tAC.MAX -- -- ps ps Address and control input hold time tIH(base) tIPW tCK tIS(base) 250 2 x tAC.MIN -- 350 2 x tAC.MIN -- ps ps ps DQ low-impedance time from CK / tLZ(DQ) CK DQS low-impedance from CK / CK tLZ(DQS) Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS Data hold skew factor Average periodic refresh Interval Auto-Refresh to Active/AutoRefresh command period tAC.MAX tAC.MAX -- 12 -- 400 7.8 3.9 -- -- 1.1 0.60 -- -- -- tAC.MAX tAC.MAX -- 12 450 7.8 3.9 -- -- 1.1 0.60 -- -- -- tAC.MIN 2 0 tAC.MIN 2 0 -- -- -- 105 tMRD tOIT tQH tQHS tREFI tRFC tCK ns ps s s ns ns 2) 3) tHP - tQHS -- -- -- 105 tHPQ - tQHS -- Precharge-All (4 banks) command tRP period Read preamble Read postamble Active bank A to Active bank B command period Internal Read to Precharge command delay Data Sheet tRP + 1tCK 0.9 0.40 7.5 10 7.5 tRP + 1tCK 0.9 0.40 7.5 10 7.5 tRPRE tRPST tRRD tRTP tCK tCK ns ns ns 25 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Electrical Characteristics Table 17 Parameter Timing Parameter by Speed Grade - DDR2-400B & DDR2-533C (cont'd) Symbol -3.7 DDR2-533 4-4-4 Min. Write preamble Write postamble Write recovery time for write without Auto-Precharge Write recovery time for write with Auto-Precharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit active power-down mode to Read command (slow exit, lower power) Max. -- 0.60 -- 0.35xtCK 0.40 15 -5 DDR2-400 3-3-3 Min. 0.35xtCK 0.40 15 Max. -- 0.60 -- Unit Notes1) tWPRE tWPST tWR WR tCK tCK ns tWR/tCK 7.5 2 -- -- tWR/tCK 10 2 -- -- tCK ns tWTR tXARD tCK tXARDS 6 - AL -- 6 - AL -- tCK Exit precharge power-down to any tXP valid command (other than NOP or Deselect) Exit Self-Refresh to non-Read command Exit Self-Refresh to Read command 2) 0 TCASE 85 C 3) 85 C < TCASE 95 C 2 -- 2 -- tCK tXSNR tXSRD tRFC +10 200 -- -- tRFC +10 200 -- -- ns tCK 1) For details and notes see the relevant INFINEON component data sheet Table 18 Symbol ODT AC Electrical Characteristics and Operating Conditions Parameter / Condition ODT turn-on delay ODT turn-on ODT turn-on (Power-Down Modes) ODT turn-off delay ODT turn-off Values Min. Max. 2 2 Unit Notes tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD tCK ns ns 2) 1) tAC.MIN tAC.MAX + 1 ns tAC.MIN + 2 ns 2 tCK + tAC.MAX + 1 ns 2.5 2.5 tCK tAC.MIN tAC.MAX + 0.6 ns ns ODT turn-off (Power-Down Modes) tAC.MIN + 2 ns 2.5 tCK + tAC.MAX + 1 ns ns ODT to Power Down Mode Entry Latency 3 -- tCK ODT Power Down Exit Latency 8 -- tCK 1) ODT turn on time min. is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measure from tAOND. 2) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD. Data Sheet 26 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes 5 Table 19 SPD Codes SPD Codes for HYS64T32000HM-3.7-A HYS64T32000HM-3.7-A HYS64T64020HM-3.7-A 512 MB x64 2 Ranks (x16) PC2-4200M-444 Rev. 1.1 HEX 80 08 08 0D 0A 61 40 00 05 3D 50 00 82 10 00 00 0C 04 38 00 08 00 01 27 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Data Sheet Description Programmed SPD Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level PC2-4200M-444 Rev. 1.1 HEX 80 Total number of Bytes in EEPROM 08 08 0D 0A 60 40 00 05 tCK @ CLmax (Byte 18) [ns] 3D tAC SDRAM @ CLmax (Byte 18) [ns] 50 Error Correction Support (nonECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes Component Attributes 00 82 10 00 00 0C 04 38 00 08 00 01 HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 19 SPD Codes for HYS64T32000HM-3.7-A HYS64T32000HM-3.7-A HYS64T64020HM-3.7-A 512 MB x64 2 Ranks (x16) PC2-4200M-444 Rev. 1.1 HEX 3D 50 50 60 3C 28 3C 2D 40 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28 00 53 72 52 28 Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Description PC2-4200M-444 Rev. 1.1 HEX 3D 50 50 60 3C 28 3C 2D 40 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28 00 53 72 52 tCK @ CLmax -1 (Byte 18) [ns] tAC SDRAM @ CLmax -1 [ns] tCK @ CLmax -2 (Byte 18) [ns] tAC SDRAM @ CLmax -2 [ns] tRP.min [ns] tRRD.min [ns] tRCD.min [ns] tRAS.min [ns] Module Density per Rank tAS.min and tCS.min [ns] tAH.min and tCH.min [ns] tDS.min [ns] tDH.min [ns] tWR.min [ns] tWTR.min [ns] tRTP.min [ns] Analysis Characteristics tRC and tRFC Extension tRC.min [ns] tRFC.min [ns] tCK.max [ns] tDQSQ.max [ns] tQHS.max [ns] PLL Relock Time TCASE.max Delta / T4R4W Delta Psi(T-A) DRAM T0 (DT0) Data Sheet Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 19 SPD Codes for HYS64T32000HM-3.7-A HYS64T32000HM-3.7-A HYS64T64020HM-3.7-A 512 MB x64 2 Ranks (x16) PC2-4200M-444 Rev. 1.1 HEX 2B 1D 1D 23 16 36 1C 30 00 00 00 00 11 C0 C1 00 00 00 00 00 00 00 xx 36 34 54 36 29 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 Data Sheet Description T2N (DT2N, UDIMM) or T2Q ( (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W S Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 JEDEC ID Code of Infineon (1) JEDEC ID Code of Infineon (2) JEDEC ID Code of Infineon (3) JEDEC ID Code of Infineon (4) JEDEC ID Code of Infineon (5) JEDEC ID Code of Infineon (6) JEDEC ID Code of Infineon (7) JEDEC ID Code of Infineon (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3 Product Type, Char 4 PC2-4200M-444 Rev. 1.1 HEX 2B 1D 1D 23 16 36 1C 30 00 00 00 00 11 BF C1 00 00 00 00 00 00 00 xx 36 34 54 33 HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 19 SPD Codes for HYS64T32000HM-3.7-A HYS64T32000HM-3.7-A HYS64T64020HM-3.7-A 512 MB x64 2 Ranks (x16) PC2-4200M-444 Rev. 1.1 HEX 34 30 32 30 48 4D 33 2E 37 41 20 20 20 20 2x xx xx xx xx xx xx xx 00 30 Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 127 Description Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year Module Manufacturing Date Week Module Serial Number (1) Module Serial Number (2) Module Serial Number (3) Module Serial Number (4) Not used PC2-4200M-444 Rev. 1.1 HEX 32 30 30 30 48 4D 33 2E 37 41 20 20 20 20 2x xx xx xx xx xx xx xx 00 Data Sheet Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 20 SPD Codes for HYS64T32000HM-5-A HYS64T32000HM-5-A HYS64T64020HM-5-A 512 MB x64 2 Ranks (x16) PC2-3200M-333 Rev. 1.1 HEX 80 08 08 0D 0A 61 40 00 05 50 60 00 82 10 00 00 0C 04 38 00 08 00 01 50 60 31 Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Description Programmed SPD Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level PC2-3200M-333 Rev. 1.1 HEX 80 Total number of Bytes in EEPROM 08 08 0D 0A 60 40 00 05 tCK @ CLmax (Byte 18) [ns] 50 tAC SDRAM @ CLmax (Byte 18) [ns] 60 Error Correction Support (nonECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes Component Attributes 00 82 10 00 00 0C 04 38 00 08 00 01 50 60 tCK @ CLmax -1 (Byte 18) [ns] tAC SDRAM @ CLmax -1 [ns] Data Sheet Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 20 SPD Codes for HYS64T32000HM-5-A HYS64T32000HM-5-A HYS64T64020HM-5-A 512 MB x64 2 Ranks (x16) PC2-3200M-333 Rev. 1.1 HEX 50 60 3C 28 3C 28 40 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D 00 51 72 42 23 1D 19 32 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Data Sheet Description PC2-3200M-333 Rev. 1.1 HEX 50 60 3C 28 3C 28 40 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D 00 51 72 42 23 1D 19 tCK @ CLmax -2 (Byte 18) [ns] tAC SDRAM @ CLmax -2 [ns] tRP.min [ns] tRRD.min [ns] tRCD.min [ns] tRAS.min [ns] Module Density per Rank tAS.min and tCS.min [ns] tAH.min and tCH.min [ns] tDS.min [ns] tDH.min [ns] tWR.min [ns] tWTR.min [ns] tRTP.min [ns] Analysis Characteristics tRC and tRFC Extension tRC.min [ns] tRFC.min [ns] tCK.max [ns] tDQSQ.max [ns] tQHS.max [ns] PLL Relock Time TCASE.max Delta / T4R4W Delta Psi(T-A) DRAM T0 (DT0) T2N (DT2N, UDIMM) or T2Q ( (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 20 SPD Codes for HYS64T32000HM-5-A HYS64T32000HM-5-A HYS64T64020HM-5-A 512 MB x64 2 Ranks (x16) PC2-3200M-333 Rev. 1.1 HEX 1C 16 2E 1A 2D 00 00 00 00 11 08 C1 00 00 00 00 00 00 00 xx 36 34 54 36 34 30 32 30 33 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Data Sheet Description T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W S Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 JEDEC ID Code of Infineon (1) JEDEC ID Code of Infineon (2) JEDEC ID Code of Infineon (3) JEDEC ID Code of Infineon (4) JEDEC ID Code of Infineon (5) JEDEC ID Code of Infineon (6) JEDEC ID Code of Infineon (7) JEDEC ID Code of Infineon (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3 Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 PC2-3200M-333 Rev. 1.1 HEX 1C 16 2E 1A 2D 00 00 00 00 11 07 C1 00 00 00 00 00 00 00 xx 36 34 54 33 32 30 30 30 HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules SPD Codes Table 20 SPD Codes for HYS64T32000HM-5-A HYS64T32000HM-5-A HYS64T64020HM-5-A 512 MB x64 2 Ranks (x16) PC2-3200M-333 Rev. 1.1 HEX 48 4D 35 41 20 20 20 20 20 20 2x xx xx xx xx xx xx xx 00 34 Product Type Organization 256 MB x64 1 Rank (x16) Label Code JEDEC SPD Revision Byte# 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 127 Description Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year Module Manufacturing Date Week Module Serial Number (1) Module Serial Number (2) Module Serial Number (3) Module Serial Number (4) Not used PC2-3200M-333 Rev. 1.1 HEX 48 4D 35 41 20 20 20 20 20 20 2x xx xx xx xx xx xx xx 00 Data Sheet Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Package Outlines 6 Package Outlines 3.8 MAX. 2.3 MAX. 54 0.15 B 1.65 -0.25 0.1 C 2.275 0.025 2.6 0.1 2.3 0.2 0.62 0.03 3.525 0.025 5.525 0.025 (44.72) D B A 107 214 B 43.38 0.02 4.725 0.025 30 0.15 A C 0.1 0.8 0.08 0.1 M C B M 106 x 0.4 = 42.4 (3.44) (2.43) 0.4 108 1.15 2.3 Detail of contacts A-A E Contact Area B-B 1.3 0.02 0.1 M A B M 4.3 1 A 2.9 0.4 0.26 0.02 0.06 C D E 107x GLD09638 Burnished, no burr allowed Figure 4 Package Outline Raw Card A L-DIM-214-1 Data Sheet 35 1.08 -0.04 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Package Outlines 2.3 MAX. 54 0.15 B 1.65 -0.25 0.1 C 2.275 0.025 2.6 0.1 2.3 0.2 0.62 0.03 3.525 0.025 5.525 0.025 (44.72) D B A 107 214 B 43.38 0.02 4.725 0.025 30 0.15 A C 0.1 0.8 0.08 0.1 M C B M 106 x 0.4 = 42.4 (3.44) (2.43) 0.4 108 1.15 2.3 Detail of contacts A-A E Contact Area B-B 1.3 0.02 0.1 M A B M 4.3 1 A 2.9 0.4 0.26 0.02 0.06 C D E 107x GLD09668 Burnished, no burr allowed Figure 5 Package Outline Raw Card B L-DIM-214-2 Data Sheet 36 1.08 -0.04 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X HYS64T[32/64]0[0/2]0HM-[3.7/5]-A Micro-DIMM DDR2 SDRAM Modules Product Type Nomenclature (DDR2 DRAMs and DIMMs) 7 Product Type Nomenclature (DDR2 DRAMs and DIMMs) Infineon's nomenclature uses simple coding combined with some propriatory coding. Table 21 provides examples for module and component product type number as well as the field number. The detailed field description together with possible values and coding explanation is listed for modules in Table 22 and for components in Table 23. Table 21 Nomenclature Fields and Examples Field Number 1 Micro-DIMM DDR2 DRAM Table 22 1 2 3 4 HYS HYB 2 64 18 3 T T 4 64 512 5 0 16 6 2 7 0 0 8 K A 9 M C 10 -5 -5 11 -A Example for DDR2 DIMM Nomenclature Values Coding HYS 64 72 T 32 64 128 256 0 .. 9 Constant Non-ECC ECC DDR2 256 MByte 512 MByte 1 GByte 2 GByte look up table 1, 2, 4 look up table look up table Field Description INFINEON Modul Prefix Module Data Width [bit] DRAM Technology Memory Density per I/O [Mbit]; Module Density1) 1) Multiplying "Memory Density per I/O" with "Module Data Width" and dividing by 8 for Non-ECC and 9 for ECC modules gives the overall module memory density in MBytes as listed in column "Coding". Table 23 1 2 3 4 DDR2 DRAM Nomenclature Values Coding HYB Constant SSTL1.8 DDR2 256 Mbit 512 Mbit 1 Gbit 2 Gbit x4 x8 x16 look up table First Second FBGA, lead-containing FBGA, lead-free DDR2-533C DDR2-400B Field Description INFINEON Component Prefix DRAM Technology Interface Voltage [V] 18 T Component Density 256 [Mbit] 512 1G 2G 5 6 7 8 9 Raw Card Generation Number of Module 0, 2, 4 Ranks Product Variations 0 .. 9 Package, Lead-Free Status Module Type A .. Z D M R U 5+6 Number of I/Os 40 80 16 7 SO-DIMM Micro-DIMM Registered Unbuffered PC2-4200 4-4-4 PC2-3200 3-3-3 First Second 11 10 9 8 Product Variations Die Revision Package, Lead-Free Status Speed Grade N/A for Components 0 .. 9 A B C F -3.7 -5 10 11 Speed Grade Die Revision -3.7 -5 -A -B Data Sheet 37 Rev. 1.0, 2004-10 03242004-2CBE-IJ2X www.infineon.com Published by Infineon Technologies AG |
Price & Availability of HYS64T32000HM-37-A |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |