|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
SPEC NO : SPECIFICATION CUSTOMER PRODUCT MODEL NO PREPARED APPROVED SAW FILTER HDF112N F11 CHECKED D A T E 2006-5-11 CUSTOMER RECEIVED: CHECKED APPROVED DATE Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 1 of 6 SAW FILTER HDF112N F11 History Record Date Spec. No. Part No. Customer No. Modify Content Remark www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 2 of 6 SAW FILTER HDF112N F11 1. SCOPE This specification shall cover the characteristics of SAW filter F112.32N. 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -40 to +85 -45 to +85 0dBm 2.2Electronic Characteristics Part Number (fo)(MHz) Nominal Center Frequency 3dB Bandwidth(from fo)(KHz) Stop Band Attenuation (from peak level)(dB) 1)fo-5.0MHz 2)fo-3.5MHz 3)fo+/-2.0MHz 4)fo+3.5MHz 5)fo+5.0MHz (dB) Insertion Loss(at minimum loss point) (fo+/-576KHz)(sce.) Group Delay Deviation / Input/output Impedance HDF112N 112.32 +/-576min 50min 45min 30min 40min 40min 4.5max 0.5 300//1.2H www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 3 of 6 SAW FILTER HDF112N F11 3. DIMENSION 4.TEST CIRCUIT www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 4 of 6 SAW FILTER Typical Frequency Response HDF112N F11 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85 for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-2 Low temperature exposure Subject the device to -40 for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-3 Temperature cycling Subject the device to a low temperature of -40for 30 minutes. Following by a high temperature of +85 for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2.2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260 10 for 101 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2.2. 5-5 Solderability Subject the device terminals into the solder bath at 245 5 for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2.2. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2.2. 5-7 Vibration www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 5 of 6 SAW FILTER HDF112N F11 Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 6 of 6 |
Price & Availability of HDF112N |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |